Skip to content
Trailermate

Guide

Trailer lights and plug: 7 or 13 pins, adapters and faults

Updated 14 November 2026 · 6 min read

In short: Trailermate trailers have a 13-pin plug and come with an adapter for a 7-pin socket. If the lights don’t work, first check the car’s socket and the adapter, then the ground connection (pin 3) and corroded pins. With a braked trailer use a 13-pin socket: a 7-pin socket has no reversing-light signal.

Working lights are the basis of a safe trailer: without brake lights and indicators the driver behind cannot see what you are doing. This guide has the plug wiring diagrams, how adapters work, what is special about LED lights and a step-by-step fault check.

1. 7-pin or 13-pin plug?

Two 12-volt plugs are used in Europe: the 7-pin (standard ISO 1724) and the 13-pin (ISO 11446). Newer cars mostly have a 13-pin socket. The 13-pin plug has its own pin for the reversing light, and pins 9–13 for permanent power and charging, used for example by caravans.

7-pin plug (ISO 1724)

PinCodeFunctionWire colour
1LLeft indicatorYellow
254gRear fog lightBlue
331GroundWhite
4RRight indicatorGreen
558RRight tail lightBrown
654Brake lightsRed
758LLeft tail light and number plate lightBlack

13-pin plug (ISO 11446)

PinFunctionWire colour
1Left indicatorYellow
2Rear fog lightBlue
3Ground (for pins 1–8)White
4Right indicatorGreen
5Right tail light and number plate lightBrown
6Brake lightsRed
7Left tail light and number plate lightBlack
8Reversing lightGrey
9–13Permanent power, charging and their grounds (caravans); not used on Trailermate trailers–

Drawings of the plugs are in the “Plug diagrams” guide (PDF).

2. Adapter: what works and what doesn’t

When a trailer’s 13-pin plug is connected to a car’s 7-pin socket through an adapter, the indicators, brake lights, tail lights, number plate light and fog light work. The reversing light does not, because a 7-pin socket has no pin for it.

A reversing light is required on a braked (O2) trailer first registered in Estonia from 10 October 2011, and UNECE Regulation 48 makes it mandatory on O2 trailers. On an unbraked light trailer (O1) it is optional. So connect a braked trailer to a 13-pin socket, or have a 13-pin socket fitted to the car. With an unbraked trailer an adapter works well.

3. LED lights and newer cars

Many cars monitor the trailer lights by the current they draw. An LED lamp draws several times less current than a bulb, so some cars think a bulb has failed: a warning appears on the dashboard or the indicator flashes faster. The fix is a load resistor that adds the missing load. The resistor gets hot in use, so mount it on a metal surface, away from plastic parts and wires. Easier to fit is an LED resistor with plugs that goes between the plug and the socket.

On some cars the tow bar wiring kit has to be activated, or coded, in the car’s system. The car then recognises the trailer and, for example, switches off its own rear fog light and rear parking sensors while towing. If the car does not recognise the trailer after the tow bar is fitted, ask the company that fitted it.

4. Trailer lights not working: check step by step

  1. Car socket. Test the socket without the trailer, using a test lamp or a socket tester. If there is no power at the socket, the fault is in the car.
  2. Adapter. If you use an adapter, try without it or with another adapter.
  3. Ground. Check pin 3 (white wire) and the lights’ ground connections on the frame. A poor ground is the most common cause when lights are dim or come on together with the wrong lights.
  4. Pins. Clean corroded pins on the plug and socket, and keep the plug in its holder after driving so that water does not collect in it.
  5. Fuses. Check the car’s fuses and the fuse of the tow bar module.
  6. Bulb and holder. If only one light does not work, check the bulb or LED lamp and the bulb holder: holders can oxidise over time.
  7. Cable. Look for a broken or pinched spot, especially at the drawbar and where the cable bends.
  8. Car and LED. If everything else is fine but the car shows a warning, see the load resistor and coding above.

Typical symptoms

SymptomLikely cause
No lights work at allno power at the car socket (fuse, tow bar module), faulty adapter or plug
Lights are dim or come on together with the wrong lightspoor ground connection (pin 3 or the light’s ground on the frame)
One particular light does not workbulb or LED lamp, corroded bulb holder, broken wire
The indicator flashes fast or the car shows a warningthe car does not recognise LED lights: a load resistor or coding is needed
The reversing light does not workthe trailer is connected through a 7-pin adapter

Lights, plugs, adapters and cable harnesses are under lights and electrics.

5. Boat trailers and water

Water can short-circuit the electrical system. If you have to drive the trailer into the water, unplug it and let the bulbs cool for 10 minutes; with LED lights unplugging is not needed. On a trailer with removable lights, take the lights off before launching. See also how to choose a boat trailer.

6. Which lights a trailer must have

The requirements come from UNECE Regulation 48 and, in Estonia, the regulation on technical requirements for motor vehicles and trailers. In short, a trailer must have:

  • rear position lights, brake lights, indicators and a number plate light;
  • a rear fog light (on trailers first registered from 1998);
  • a reversing light on a braked (O2) trailer first registered from 10 October 2011;
  • two red triangular reflectors at the rear, white reflectors at the front and reflectors on the sides;
  • white front position lights on a trailer wider than 1600mm, end-outline marker lights on a trailer wider than 2100mm, and side marker lights on a trailer longer than 6m (including the drawbar).

Trailermate box trailers and trailers with lids have waterproof LED front lights, the rear lights sit in welded, hot-dip galvanised steel housings that protect them while loading, and the wiring runs inside the frame, protected from knocks and moisture.

See also the trailer maintenance guide.

Frequently asked questions

Can a trailer with a 13-pin plug be connected to a car with a 7-pin socket?
Yes, with an adapter. All lights except the reversing light work. A reversing light is required on a braked trailer, so use a 13-pin socket with one.
Why does the car show a warning with an LED-lit trailer?
An LED lamp draws less current and the car thinks a bulb has failed. A load resistor or coding the car for the trailer helps.
Why are the trailer lights dim or mixed up?
Almost always because of a poor ground: check pin 3 of the plug and the lights’ ground connections on the frame.
Must a trailer have a fog light?
Yes. A rear fog light is mandatory on a trailer first registered from 1998.

Matching spare parts

Lights and electrics →

More guides

Licence calculator

B: trailer up to 750kg, or car + trailer up to 3500kg in total.

Questions? Call us.

Mon–Fri 9–16

Request a quote
New address soon

We are moving

Soon you will find our production and sales at Tule 29, Saue. Opening hours stay the same: Mon–Fri 9–16.
On-site purchases by prior arrangement.

Delivery may take longer than usual while we move. We apologise!

Cart

We are moving to new premises, so delivery may take longer than usual right now. We apologise! We will confirm the exact delivery time when you order. Or contact us.