Skip to content
Trailermate

Guide

Securing a load on a trailer

Updated 14 November 2026 · 6 min read

In short: put the heavier part of the load over the axle and against the front gate, strap it to the trailer’s lashing eyes so that it cannot move forwards, backwards or sideways, and check the straps again after the first few kilometres. An unsecured load moves even with light braking or a sharp bend – and the driver is always responsible.

Securing a load is not just a legal requirement. A moving load changes how the trailer handles, can damage the trailer and the cargo, and puts other road users at risk. This guide explains how to place and secure a load on a trailer correctly.

Why does a load move?

While driving, the load is pushed by forces that are bigger than they seem:

  • When braking the load pushes forwards with up to about 80% of its weight. A 300kg load pushes forwards with a force of roughly 240kg under hard braking.
  • In bends and when accelerating up to about 50% of the load’s weight acts sideways and backwards.

Friction with the floor alone does not hold the load in place: on bumps the load lifts for a moment and slides. That is why a load must always be secured, even if it “feels heavy”.

1. Place the load correctly

Correct placement does half the work of securing.

  • The heavier part over the axle. The trailer’s centre of gravity should be over the axle or slightly in front of it.
  • Against the front gate. When the load rests against the front gate, it cannot slide forwards when you brake. Fill empty gaps so the load cannot gather speed.
  • Heavy at the bottom, light on top. A low centre of gravity keeps the trailer stable.
  • Evenly between the sides. A trailer loaded to one side leans and wears the tyres and bearings on that side.

Nose weight: not too little, not too much

Nose weight is the force with which the trailer’s drawbar presses down on the car’s tow ball. If it is too low (load too far back), the trailer starts to snake at speed. If it is too high, it overloads the car’s rear axle and worsens steering. The correct value is given in the car’s registration certificate or owner’s manual; it is usually 50–100kg. Check it with scales under the jockey wheel.

2. Use the right straps

  • A strap’s strength is printed on its label. Look for LC (lashing capacity, daN): 1 daN ≈ 1kg. For example, an LC 400 daN strap holds about 400kg in a straight pull.
  • When strapping over the load (the load is pressed down onto the floor) the label’s STF value counts – the strap’s tensioning force. The higher the STF, the harder the load is pressed onto the floor.
  • Several straps are better than one strong strap. Use at least two straps, more for a longer load.
  • Replace worn straps. A strap that is frayed, cut or has damaged stitching will not hold the load.
  • Protect sharp edges. Corner protectors stop the strap from being cut and the load from being damaged.

3. Fasten the load to the trailer’s lashing points

Straps must be fastened to the trailer’s lashing eyes, not to the top edge of the sides or to the hinges.

  • Trailermate box trailers have 8 lashing eyes in the box floor and 6 welded eyes on the outer sides, bolted through the frame rather than riveted to the side panel.
  • Extra lashing eyes can be fitted to an older trailer. Suitable eyes are under gate locks, hinges and strap eyes.

Two main ways of securing

  1. Top-over lashing (pressing onto the floor): the strap runs over the load and presses it onto the floor. Suits a tightly packed load such as boxes, bags and boards. An anti-slip mat under the load increases friction several times.
  2. Direct lashing: the strap ties the item directly to the trailer’s eyes, at an angle forwards and backwards. Suits machines, motorcycles and other wheeled or tall items.

4. Checklist before you drive

  • The heavier part is over the axle and against the front gate.
  • The nose weight is within the car’s limit.
  • The trailer’s gross weight does not exceed the permitted one (see the trailer’s type plate).
  • The load is secured with at least two straps, and the straps are not twisted or worn.
  • Sharp edges have corner protectors.
  • The gates and gate locks are closed.
  • Loose material (branches, waste, sand) is covered with a tarpaulin or net.
  • A long load is visibly marked at the rear.
  • After the first 5–10km, stop and tighten the straps again – the load always settles a little at the start of a trip.

Special cases

Motorcycle or ATV

Put the front wheel in a motorcycle wheel chock and lash the vehicle with four straps directly to the eyes: two forwards, two backwards. Fasten the straps to the frame or the lower part of the fork, not to the handlebars or plastic parts.

Long load (boards, pipes)

A long load must be supported along its whole length and must not cover the lights or the number plate. If the load sticks out more than 1 metre behind the trailer, mark its furthest point with a projecting-load marker (for example a red and white flag) and, in the dark, a red light. The load may not stick out more than 2 metres behind the trailer.

Loose material (branches, waste, sand)

Always cover the load with a tarpaulin or net. Unsecured loose material blows out while driving, endangers others and can be fined. A trailer with a lid is the easiest solution.

Need a trailer that is ready for securing loads straight away? Trailermate box trailers have a hot-dip galvanised fully welded frame, lashing eyes bolted through the frame and front and rear gates reinforced with waterproof plywood. See also the trailer maintenance and safe use guide.

Frequently asked questions

Does a heavy load also need securing?
Yes. When braking, a heavy load pushes forwards with the same share of its weight as a light one – so the force is much larger.
How many straps do I need?
At least two. For a longer or taller load add more, so that the load cannot move forwards, backwards or sideways.
Can I fasten straps to the top edge of the sides?
No. The sides are not designed for the pull of a strap. Use the trailer’s lashing eyes.
Does the load need securing in a trailer with a lid?
Yes. The lid keeps the load dry and protects it, but it does not stop the load from moving inside the box and damaging the lid and the sides.
Who is responsible for securing the load?
The driver. Even if someone else loaded the trailer, the driver must check before driving that the load is secured correctly.

More guides

Licence calculator

B: trailer up to 750kg, or car + trailer up to 3500kg in total.

Questions? Call us.

Mon–Fri 9–16

Request a quote
New address soon

We are moving

Soon you will find our production and sales at Tule 29, Saue. Opening hours stay the same: Mon–Fri 9–16.
On-site purchases by prior arrangement.

Delivery may take longer than usual while we move. We apologise!

Cart

We are moving to new premises, so delivery may take longer than usual right now. We apologise! We will confirm the exact delivery time when you order. Or contact us.