Skip to content
Trailermate

Guide

Trailer hub, bearing and brake cable: how to find the right spare part

Updated 14 November 2026 · 6 min read

In short: first find the maker of your axle and the brake size (for example KNOTT 160×35 or AL-KO 2051). For a bearing, measure the inner diameter × outer diameter × width (for example 34x64x37). For a brake cable, measure two lengths – the sheath length (H) and the cable length (S), for example 1030/1240mm – and check whether the cable end is threaded or has a mushroom head.

Hubs, bearings and brake cables are the parts of a trailer’s running gear that wear the most – and they are also the parts most often ordered in the wrong size. This guide explains how to find the right part first time.

1. Find the axle maker and the brake size

Everything else depends on which axle the trailer has.

  • Axle type plate: most trailers have a sticker or plate on the axle with the maker (KNOTT, AL-KO, BPW, SPP and others), the load capacity and the type code.
  • Brake size: on a braked trailer the brake size is marked on the brake back plate or the drum. The most common are 160×35, 200×50, 230×60 and 250×40 (drum diameter × brake shoe width, mm). AL-KO marks its brakes with numbers, for example 1636/1637 = 160×35, 2050/2051 = 200×50, 2360/2361 = 230×60.
  • Unbraked trailer: the hubs of an unbraked (light) trailer are simpler – the bearing dimensions are enough to find the bearings.

2. Wheel bearing: how to find the right size

Compact bearing or taper roller bearings?

  • A compact bearing (double-row angular contact ball bearing) is used on most newer trailers. It is one sealed unit that needs no adjusting or greasing. A worn compact bearing is replaced as a whole.
  • Taper roller bearings are used on older and many unbraked trailers: the hub has two bearings, inner and outer (for example 30204, 30205, 30206), which must be greased and adjusted.

How to measure a bearing

A bearing’s size is written as inner diameter × outer diameter × width in millimetres: d – the bore (the diameter of the axle stub), D – the outer diameter, B – the width. The dimensions or the bearing number are often printed on the side of the bearing. If not, measure with a caliper.

The most common trailer compact bearings

Bearing (d × D × B)Where it is used (examples)Hub cap
30×60×37mmSPP hubs, lighter unbraked axlesØ 60mm
34×64×37mmKNOTT and AL-KO 160×35 and 200×50 brake hubs, many 750–1350kg axlesØ 64mm
39×72×37mmheavier axles, e.g. larger brakes (230×60, 250×40)Ø 72mm

The hub cap diameter usually matches the bearing’s outer diameter, so the cap size helps to identify the bearing. Bearings, seals and caps are under bearings and hubs.

When to replace a bearing?

  • the wheel has play when you rock it up and down;
  • the bearing is noisy, grinds or runs hot while driving;
  • the area around the hub is greasy or the cap is missing.

When replacing, remember:

  1. Always replace bearings in pairs on one axle (both wheels).
  2. The hub nut is single-use. The self-locking nut of a compact-bearing hub must be replaced with a new one when the bearing is changed (see hub nut).
  3. Tighten the nut to the torque specified by the axle maker – a nut that is too tight or too loose quickly ruins a new bearing.
  4. Fit a new or undamaged hub cap: without a cap, water and dirt get into the bearing.
  5. On a boat trailer use waterproof bearings or hubs – KNOTT offers a separate waterproof version of the same hub.

3. Brake cable: how to choose the right one

The brake cable connects the brake mechanism in the trailer’s coupling to the wheel brake. Usually each wheel has its own cable, and on the coupling side they are joined through a compensator (balance bar).

What do the two numbers on a cable mean?

A brake cable’s size is written with two numbers, for example 1030/1240:

  • H – sheath length (1030mm): the length of the outer sheath from end fitting to end fitting;
  • S – cable length (1240mm): the total length of the inner steel cable.

Measure the old cable the same way. If the old cable is broken, measure the cable on the other wheel of the same axle.

Threaded end or mushroom head?

  • Threaded end: the cable end is fastened with a nut. Used on many KNOTT and AL-KO brakes.
  • Mushroom head: a quick-fit end, where the mushroom-shaped end of the cable hooks into the compensator. For example, the KNOTT compensators 409904.001 (single axle) and 409906.001 (tandem) are made for mushroom-head cables.

If the end is the wrong type, the cable cannot be fitted – even if the length is right.

Cables by maker

  • KNOTT: threaded cables (series 33921) and quick-fit mushroom-head cables (series 980202), lengths given as H/S. Stainless cables are available for boat trailers.
  • AL-KO: for example, Profi Longlife cables fit AL-KO brakes 1636G/1637/2051/2361, lengths also given as H/S.

All KNOTT and AL-KO brake cables and brake shoes are under brakes and cables.

When to replace a brake cable?

  • the cable is seized or moves stiffly in the sheath;
  • the sheath is cracked or rusty;
  • the brakes do not release after braking and the wheel gets hot;
  • the trailer pulls to one side when braking.

Preferably replace cables in pairs, and adjust the brakes after replacing them.

4. Original part or B part?

For many parts our shop has two options:

  • An original part (KNOTT, AL-KO, etc.) is the axle maker’s own part. We recommend it for newer trailers and where the maker’s warranty matters.
  • A B part is a replacement made by another manufacturer to the original dimensions. It is cheaper and well suited to an older trailer.

Either way, the size, brake type and cable end must match your trailer. Other running-gear parts are in the spare parts section.

For regular checks of bearings and brakes, see also the trailer maintenance guide.

Frequently asked questions

Does a 34x64x37 bearing fit every 750kg trailer?
No. It is a common size, but 30x60x37 and 39x72x37 bearings are also used, and older trailers have taper roller bearings. Measure the old bearing or check the axle maker’s data.
Can the bearing be replaced without replacing the hub?
Usually yes. If the hub’s bearing seat is worn or the drum surface is damaged, the whole hub must be replaced.
Must the brake cable length be exactly the same?
Yes, both dimensions (H and S) must match. A cable that is too long does not let the brakes be adjusted correctly; one that is too short will not fit.
Can I fit an AL-KO cable to a KNOTT axle?
Generally not. The end fittings and mountings differ between makers – choose a cable made for your type of brake.

More guides

Licence calculator

B: trailer up to 750kg, or car + trailer up to 3500kg in total.

Questions? Call us.

Mon–Fri 9–16

Request a quote
New address soon

We are moving

Soon you will find our production and sales at Tule 29, Saue. Opening hours stay the same: Mon–Fri 9–16.
On-site purchases by prior arrangement.

Delivery may take longer than usual while we move. We apologise!

Cart

We are moving to new premises, so delivery may take longer than usual right now. We apologise! We will confirm the exact delivery time when you order. Or contact us.